Martin Professional CX-10 Extreme Bedienungsanleitung

CX-10 Extremeuser manual

10 CX-10if they are to respond identically: they will receive the same instructions and individual control will not bepossible.TO SET THE DMX ADDRESS

Control Panel 11LAMP HOURS Read the total number of lamp hours since fabrication (INFO>TIME>L HR>TOTL), and the numberof lamp hours since th

12 CX-10UPLOAD MODEThe upload mode command (UTIL>UPLd) prepares the fixture for a software update. This command isnot necessary, however, as uploa

DMX-512 control 13DMX-512 CONTROLThis section briefly describes the DMX-controllable effects. See also the DMX table starting on page 32 andthe DMX c

14 CX-10Speed controlTRACKING CONTROLTracking control is enabled by setting the Effects speed channel (10) to 0. With tracking control, the speed at

Optical configuration 15OPTICAL CONFIGURATIONThis chapter contains the following sections:• Effect wheel• “Color filters” on page 18• “Optional lense

16 CX-10Position Lamp-side effect wheel Front-lens-side effect wheel Combined effect1 Open gobo, +22,5/17 HT-painted2 Gobo with 12 mm hole3 Gobo with

Optical configuration 17REPLACING AN EFFECT FLAG1 Disconnect the fixture from AC power and allow it to cool. 2 Remove the cover.3 Turn the effect whe

18 CX-10Color filtersSTANDARD CONFIGURATIONThe CX-10 provides 12 dichroic color filters as shown below.REPLACING A COLOR FILTER1 Disconnect the fixtu

Optical configuration 19Optional lensesThe standard 22 degree lens can be changed to 14 or 32 degrees using two separately orderable lens kits.See Ac

217109340412© 2003 Martin Professional A/S, Denmark.All rights reserved. No part of this manual may bereproduced, in any form or by any means, without

20 CX-10replace the standard front glass with the glass lens supplied in the narrow-angle lens kit. Replace the frontglass module.8 Ensure that the d

Optical configuration 219 Using a Phillips screwdriver, replace the focus module.10 Replace the fixture cover before applying power.

22 CX-10Animation wheelsAn animation wheel can replace, or be affixed to the color wheel. This requires an Animation Wheel AdaptorKit and an animatio

Optical configuration 23Linear breakup: The Linear Breakup disc (P/N 62400223) providesrhythmic movement and can be used to simulate a breeze through

24 CX-10Flicker wheel: The Flicker Wheel (P/N 62400222) provides a different kindof effect and can be used at high speed for motion effects, such as

Optical configuration 255 Remove the effects wheel and then the color wheel using a 2.5 mm hex wrench.The wheels are held in place using clamps that

26 CX-10Note: If at a later time you remove the animation wheel then use the control menu to select the wheel (WHEL) personality (under the PERS menu

Optical configuration 27ensure that the wheel does not come into contact with anything that might hinder its free rotation. Clamp theeffects wheel in

28 CX-10SERVICEThe CX-10 requires regular maintenance to keep performing at their peak. Excessive dust, grease, andsmoke fluid buildup degrades perfo

Service 29INSTALLING A LAMPWARNING! When replacing the lamp, disconnect the fixture from AC power and allow the lamp to cool for at least 15 minutes

3Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Features ...

30 CX-10FANTo maintain adequate cooling it is important that the fan becleaned regularly. 1 Remove the fan by pulling out the locking pins on eachsid

Service 31Updating softwareThe latest CX-10 firmware is available from the support area of the Martin web site athttp://www.martin.com. It can be ins

DMX PROTOCOL Channel Value Percent Function11- If DMX Reset is disabled in the menu, a reset command can only be executed if the CTC filter is selecte

DMX protocol 33401224364860728496108120132144156 - 159160 - 163164 - 167168 - 171172 - 175176 - 179180 - 183184 - 187188 - 191192 - 195196 - 199200 -

34 CX-10CONTROL MENU Menu Item Options Notes (Default settings in bold print)AddR - 1-512DMX addressPERS dISP ONDisplay remains onOFFDisplay extingu

Control menu 35MAN RST -Reset fixtureL ON -Lamp onLoFF -Lamp offSHUT OPENOpen shutterCLOSClose shutterSTRFFast strobeSTRMMedium strobeSTRSSlow strobe

36 CX-10UTIL(Press and hold Enter for a few seconds) Adj -Not implemented.CAL d1OFDimmer flag 1 offsetd2OFDimmer flag 2 offsetCoOFColor wheel offsetG

Error messages 37ERROR MESSAGESDisplay readout Appears if... What to doMERR (Memory error) ...the EEPROM memory cannot be read. • Contact service te

38 CX-10TROUBLESHOOTINGProblem Probable cause(s) RemedyOne or more of the fixtures is completely dead.No power to fixture. • Check that power is swit

PCB connections 39PCB CONNECTIONS33120048-A3 Dim 13 Dim 14 Dim 24 Dim 26 Effect6 Effect7 Focus7 Focus8 Color8 Color9 Frost9 Frost

4 CX-10INTRODUCTIONFeaturesThank you for selecting the Martin CX-10 Extreme. Some of the many features include: • efficient, 2000 hour, 250 watt disc

40 CX-10SPECIFICATIONS - CX-10PHYSICALLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications - CX-10 41CONTROL AND PROGRAMMINGData input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety 5SAFETYWarning! This product is for professional use only. It is not for household use.This product presents risks of lethal or severe injury

6 CX-10SETUPUnpackingThe CX-10 comes with:• MSD 250/2 lamp• 3-meter, 3-wire IEC power cable•user manualThe packing material is carefully designed to

Setup 7INSTALLING A PLUG ON THE POWER CABLEThe power cable must be fitted with a grounding-type cord cap that fits your power distribution system.Con

8 CX-105 Install a safety cable that can hold at least 10 times the weight of the fixture through/over the support andanywhere through the fixture’s

Control Panel 9CONTROL PANELYou set the address and personalities, read out data, and execute service utilities from the control panel.Settings can a